5006A SURROUND KIT WITH FIVE d:dicate™ 4006A, CLIPS AND WINDSCREENS IN PELI™ CASE
This is a complete Surround Kit with five carefully factory-matched omnidirectional microphones. Even though the standard tolerances on the d:dicate™ 4006A Omnidirectional Microphones are extremely low, the surround match is even closer.
The specially selected d:dicate™ 4006A Omnidirectional Microphones are matched within ±0.5 dB on both frequency response and sensitivity from mean of set.
The natural sound, high sensitivity, low noise-floor and extremely linear frequency response from 10 Hz to 20 kHz (±2 dB) of the microphones make the d:dicate™ 4006A Omnidirectional Microphones the perfect choice for all AB Stereo, Decca Tree or surround main array recordings. The precise reproduction, total transparency and natural-sounding clarity of d:dicate™ 4006A Omnidirectional Microphones will provide you with a lifetime of satisfying listening.
The foam design in the heavy-duty transportation box allows for fast and easy exchange of microphone/accessory inlays.
Bundle deal
You save 500 EUR off the list price when you buy S5 Surround Mount along with this Matched Surround Kit. The deal also applies to:
d:mension™ 5006-11A Surround Kit with d:dicate™ 4006A Omnidirectional and d:dicate™ 4011A Cardioid Microphones
d:mension™ 5015A Surround Kit with dicate™ 4015 Wide Cardioid Microphones
Features
The product offers the following features
Wide pickup area and natural sound
Five carefully matched microphones
Ambience pickup with convenient directionality
Peli™ Case transportation and protection
Frequency response with Free-field Grid
Frequency response with Close-miking Grid
Frequency response with Diffuse-field Grid
Frequency response with Nose Cone
Polar pattern with Free-field Grid
Polar pattern with Close-miking Grid
Polar pattern with Diffuse-field Grid
Polar pattern with Nose Cone
Polar pattern with Nose Cone – Vertical
Typical on and off-axis response of a 4006A
Specifications
d:mension™ Surround Solutions 5006A SURROUND KIT WITH FIVE d:dicate™ 4006A, CLIPS AND WINDSCREENS IN PELI™ CASE
Directional patternOmnidirectional
Principle of operationPressure
Cartridge typePre-polarized condenser
Frequency range10 Hz – 20 kHz
Frequency range, ±2 dB10 Hz – 20 kHz
Sensitivity, nominal, ±2 dB at 250 Hz40 mV/Pa; -28 dB re. 1 V/Pa
Equivalent noise level, A-weightedTyp. 15 dB(A) re. 20 µPa (max. 17 dB(A))
Equivalent noise level, ITU-R BS.468-4Typ. 27 dB (max. 29 dB)
S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL)Typ. 79 dB(A)
Total harmonic distortion (THD)< 1% up to 139 dB SPL peak
Dynamic rangeTyp. 124 dB
Max. SPL, peak before clipping146 dB
Switchable attenuator, filters etc.0 dB / -20 dB
Output impedance 200 Ω
Minimum load impedance2 kΩ
Cable drive capability100 m (328 ft)
Output balance principleImpedance balancing with Active Drive
Common mode rejection ratio (CMRR)> 60 dB
Power supply (for full performance)48 V Phantom power (± 4 V)
Current consumption2.8 mA
ConnectorXLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: – phase
ColorMatte black
Weight163 g (5.7 oz)
Microphone diameter16 – 19 mm (0.6 – 0.75 in)
Capsule diameter16 mm (0.6 in)
Microphone length170 mm (6.7 in)
Maximum output voltage, RMS8 V
Polarity+V at pin 2 for positive sound pressure
Temperature range-40°C to 45°C (-40°F to 113°F)
Relative humidity (RH)Up to 90%
Matching tolerance (frequency response and sensitivity)±0.5 dB
Phase deviation for kit< 5°